I'm starting to think that this overclock is not significant and maybe i've been unlucky on the silicon lottery, as i've seen a lot of people achieve + 100 on the gpu boost clock. I can't get any higher than + 50 without the gpu crashing. I applied these settings as my overclock: Before my overclock the clocks sat around the 1980 - 2000 MHz range, whereas now they sit at 2038 MHz. Also i'm sure the clocks are higher after my overclock according to HW-Monitor. Yeah i've disabled vsync / enabled ulimited fps to make sure the fps isn't capped to my refresh rate (144hz). If that's not the case, are the clocks actually higher than before the OC while playing said game? The GPU will not run on the highest clocks if there's not enough load. Dumb question - are you sure you are not reaching a set fps cap ingame (either by an fps cap or vsync/gsync)? In my case, it does not properly apply, even though I am not quitting the tool after dialing in the OC.Īnyway, no fps gain is indeed strange. Okay, so that is different from my experience. If it helps these are the preset OC mode settings and my manual overclock settings.ĪSUS GPU Tweak 2 Preset OC mode settings: Now my question is, does the GPU Tweak software have to be running at all times, (checking the setting that says start GPU Tweak at boot time) or can I close the program and not have to run it all the time and after a reboot it will still apply my overlock settings still? Which indicates to me that overclocking my gpu does nothing to improve performance or that the GPU Tweak software is not applying settings. All three of these gpu settings changed in the GPU Tweak software yield the exact same results in both games and benchmarking software in terms of average fps values. P.S: Phaase88 recommended me limiting the power usage but it didint help and took a lot of performance.Hi there, i'm using the ASUS GPU Tweak 2 on my ASUS Strix 1080ti (OC edition) and i've tried testing the default gpu mode, GPU Tweaks built in preset OC mode and my own manual overclock on the gpu. Will using it factory settings damage my GPU or should i undervolt it to be safe? thanks for answers. İt used to be 80-85c but didn't make this level of fan noise. RTX 3060ti has the same size of Saphires cooler. So ı used to own a Sapphire Pulse RX6600 8GB. After those results ı did a bit of googling and found about undervaluing ( ) fan curve settings and +600 memory clock. After turning it on the temps went like 82-79c. It was reaching 87c and ı decided to turn on V-SYNC. I waited for it to cool down and install cyberpunk and ı decided to play it. While waiting i decided to download cyberpunk 2077. the card reached like 90c and decided to close the game and wait for it to cool down. After that ı just kept playing like that. After 1 or 2 minutes the card started reaching 82c and the fans started going crazy (2700RPM). I put in high settings with 144Hz and dlls quality. After that, i went on installing my favorite game battlefield 2042. I was happy with the results and i approved the purchase. The software bugged out when we clicked 'Sync All Cards' and basically sent too many volts (over the amount we set) into one of the cards. Last night, I was helping a friend overclock his two ASUS ROG 780 ti's and we ended up bricking one of the cards by using ASUS GPU tweak. I oppened the box it came from china and it had no warranty before starting to write my problem ı want to let everyone know that my casses are flow is good.(Aerocool One Duo).I installed the gpu and ran furmark on it. I'm fairly experienced when it comes to overclocking video cards. I bought This Asus dual mini OC RTX 3060ti LHR from second hand. So yesterday ı opened a thread about this topic to this form.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |